IS 1786:2008 with CRS chemistry

Fe 500 CRS TMT Steel Bar

Copper and chromium alloying slows chloride attack — the standard specification within a few kilometres of the sea.

Mill test certificate Fe 500 CRS

Standard: IS 1786:2008 with CRS chemistry
Yield stress: 500 N/mm² min
UTS: 545 N/mm² min
Elongation: 12.0% min
Carbon max: 0.30%
S + P max: 0.175%
Bend / re-bend: 4d / 5d
Sizes held: 8, 10, 12, 16, 20, 25, 32 mm

Despatch to any site in IndiaHeat no. on every tag

Specification

Fe 500 CRS specification

Corrosion resistant steel with controlled copper, chromium and phosphorus. Copper and chromium alloying slows chloride attack — the standard specification within a few kilometres of the sea.

Yield strength: 500 MPa min
Tensile strength: 545 MPa min
Elongation: 12.0% min
TS / YS ratio: 1.08 min

Mechanical and chemical requirements for Fe 500 CRS under IS 1786:2008 with CRS chemistry. These are the minimums we test against before a load is released.
Property	Requirement	Why it matters on site
0.2% proof / yield stress	500 N/mm² min	Sets how much load each bar carries, so it drives the steel quantity in your design
Ultimate tensile strength	545 N/mm² min	The reserve above yield before the bar actually breaks
TS / YS ratio	1.08 min	A higher ratio means the structure warns you before it fails
Elongation on gauge length	12.0% min	How far the bar stretches before fracture — this is what lets you bend it on site
Bend test	4d / 5d	No cracking on the outside of the bend at the specified mandrel
Re-bend test	5d / 7d	Catches embrittlement after ageing, which is where cheap bar fails
Carbon	0.30% max	Lower carbon means better weldability and less brittleness
Sulphur	0.055% max	Excess sulphur causes hot shortness and cracking
Phosphorus	0.120% max	Excess phosphorus makes the bar brittle in cold weather
Sulphur + phosphorus	0.175% max	The combined limit is the single best indicator of primary versus secondary steel

Fe 500 CRS weight chart

Sizes of Fe 500 CRS we hold, with nominal sectional area and unit weight. Actual weight is checked on our weighbridge and held inside ±2% of these figures.
Diameter	Area (mm²)	Weight (kg/m)	Per 12 m bar (kg)	Bars per tonne
8 mm	50.3	0.395	4.74	211
10 mm	78.5	0.617	7.40	135
12 mm	113.1	0.888	10.66	94
16 mm	201.1	1.580	18.96	53
20 mm	314.2	2.470	29.64	34
25 mm	490.9	3.850	46.20	22
32 mm	804.2	6.310	75.72	13

Where Fe 500 CRS is the right call

Best used for: Coastal and marine construction, sewage and effluent works, chemical plants, high-humidity and high-chloride sites.

Think twice about: Dry inland sites, where the corrosion premium buys nothing.

Fe 500 CRS suppliers by city

Every city page carries the local delivery position, lead time and freight note.

Other grades

Compare against the rest

Fe 415415 MPa · 14.5% elong. Fe 415D415 MPa · 18.0% elong. Fe 500500 MPa · 12.0% elong. Fe 500D500 MPa · 16.0% elong. Fe 500S500 (max 625) MPa · 18.0% elong. Fe 550550 MPa · 10.0% elong. Fe 550D550 MPa · 14.5% elong. Fe 600600 MPa · 10.0% elong.

Questions

Fe 500 CRS — common questions

What does Fe 500 CRS mean?

Fe is iron, the number is the minimum yield strength in newtons per square millimetre. Fe 500 CRS therefore yields at no less than 500 N/mm². CRS means corrosion resistant steel, alloyed with copper and chromium.

Where is Fe 500 CRS used?

Coastal and marine construction, sewage and effluent works, chemical plants, high-humidity and high-chloride sites.

What is the elongation of Fe 500 CRS?

12.0% minimum on the specified gauge length under IS 1786:2008 with CRS chemistry. Elongation is what lets the bar be bent on site without cracking, and it is the number to check before you accept a cheaper alternative.

Is Fe 500 CRS available in all diameters?

We hold 8, 10, 12, 16, 20, 25, 32 mm in 12 metre lengths. Anything outside that is rolled to order against confirmed tonnage.

What is the minimum order quantity?

Five tonnes for delivered loads. Below that you are welcome to lift from our stockyard directly, and we will still issue the mill test certificate.

How is the price fixed?

Basic rate per tonne, plus GST at 18%, plus freight to your site. We quote the three separately so you can see exactly what you are paying for.

Do you supply mill test certificates?

Yes, with every despatch. The heat number on the certificate matches the tag on the bundle, so it survives an audit.