IS 1786:2008

Fe 500 TMT Steel Bar

The volume grade — roughly two out of three tonnes moving through any Indian stockyard.

Mill test certificate Fe 500

Standard: IS 1786:2008
Yield stress: 500 N/mm² min
UTS: 545 N/mm² min
Elongation: 12.0% min
Carbon max: 0.30%
S + P max: 0.105%
Bend / re-bend: 4d / 5d
Sizes held: 6, 8, 10, 12, 16, 20, 25, 28, 32, 36, 40 mm

Despatch to any site in IndiaHeat no. on every tag

Specification

Fe 500 specification

The default working grade of Indian construction. The volume grade — roughly two out of three tonnes moving through any Indian stockyard.

Yield strength: 500 MPa min
Tensile strength: 545 MPa min
Elongation: 12.0% min
TS / YS ratio: 1.08 min

Mechanical and chemical requirements for Fe 500 under IS 1786:2008. These are the minimums we test against before a load is released.
Property	Requirement	Why it matters on site
0.2% proof / yield stress	500 N/mm² min	Sets how much load each bar carries, so it drives the steel quantity in your design
Ultimate tensile strength	545 N/mm² min	The reserve above yield before the bar actually breaks
TS / YS ratio	1.08 min	A higher ratio means the structure warns you before it fails
Elongation on gauge length	12.0% min	How far the bar stretches before fracture — this is what lets you bend it on site
Bend test	4d / 5d	No cracking on the outside of the bend at the specified mandrel
Re-bend test	5d / 7d	Catches embrittlement after ageing, which is where cheap bar fails
Carbon	0.30% max	Lower carbon means better weldability and less brittleness
Sulphur	0.055% max	Excess sulphur causes hot shortness and cracking
Phosphorus	0.055% max	Excess phosphorus makes the bar brittle in cold weather
Sulphur + phosphorus	0.105% max	The combined limit is the single best indicator of primary versus secondary steel

Fe 500 weight chart

Sizes of Fe 500 we hold, with nominal sectional area and unit weight. Actual weight is checked on our weighbridge and held inside ±2% of these figures.
Diameter	Area (mm²)	Weight (kg/m)	Per 12 m bar (kg)	Bars per tonne
6 mm	28.3	0.222	2.66	376
8 mm	50.3	0.395	4.74	211
10 mm	78.5	0.617	7.40	135
12 mm	113.1	0.888	10.66	94
16 mm	201.1	1.580	18.96	53
20 mm	314.2	2.470	29.64	34
25 mm	490.9	3.850	46.20	22
28 mm	615.8	4.830	57.96	17
32 mm	804.2	6.310	75.72	13
36 mm	1017.9	7.990	95.88	10
40 mm	1256.6	9.860	118.32	8

Where Fe 500 is the right call

Best used for: RCC frames, slabs, beams, columns for residential and commercial buildings up to mid-rise.

Think twice about: Seismic-critical detailing where the design specifically calls for a D grade.

Fe 500 suppliers by city

Every city page carries the local delivery position, lead time and freight note.

Other grades

Compare against the rest

Fe 415415 MPa · 14.5% elong. Fe 415D415 MPa · 18.0% elong. Fe 500D500 MPa · 16.0% elong. Fe 500S500 (max 625) MPa · 18.0% elong. Fe 550550 MPa · 10.0% elong. Fe 550D550 MPa · 14.5% elong. Fe 600600 MPa · 10.0% elong. Fe 500 CRS500 MPa · 12.0% elong.

Questions

Fe 500 — common questions

What does Fe 500 mean?

Fe is iron, the number is the minimum yield strength in newtons per square millimetre. Fe 500 therefore yields at no less than 500 N/mm².

Where is Fe 500 used?

RCC frames, slabs, beams, columns for residential and commercial buildings up to mid-rise.

What is the elongation of Fe 500?

12.0% minimum on the specified gauge length under IS 1786:2008. Elongation is what lets the bar be bent on site without cracking, and it is the number to check before you accept a cheaper alternative.

Is Fe 500 available in all diameters?

We hold 6, 8, 10, 12, 16, 20, 25, 28, 32, 36, 40 mm in 12 metre lengths. Anything outside that is rolled to order against confirmed tonnage.

What is the minimum order quantity?

Five tonnes for delivered loads. Below that you are welcome to lift from our stockyard directly, and we will still issue the mill test certificate.

How is the price fixed?

Basic rate per tonne, plus GST at 18%, plus freight to your site. We quote the three separately so you can see exactly what you are paying for.

Do you supply mill test certificates?

Yes, with every despatch. The heat number on the certificate matches the tag on the bundle, so it survives an audit.